Aluminium profile production
Profiles formed by two legs meeting at 90 degrees, also known as L sections. Used for corner joints, edge protection and reinforcement. Legs can be equal or of different lengths.
Open catalogue
| Size range | Equal legs 10–120 mm, wall thickness 0.9–13 mm; 60 standard sizes in total |
|---|---|
| Minimum order | Depends on the die and press — confirmed per project |
| Length | Cut to your required length on request |
| Surface finish | Mill finish, anodised (10–25 microns), electrostatic powder coating (RAL range) |
| Tooling | Project-based die design for sections not in our catalogue |
| Lead time | Short lead times, backed by our own die shop, our partner die makers and our press capacity |
| Shipment | Supplied with analysis report |
Equal angle profiles from our standard dies. a is the leg length, s the wall thickness.
| Code | Size a × a × s (mm) | kg/m |
|---|---|---|
| AYŞ01 | 10x10x1.2 | 0.065 |
| AYŞ02 | 10x10x2 | 0.108 |
| AYŞ03 | 15x15x1 | 0.081 |
| AYŞ04 | 15x15x1.1 | 0.089 |
| AYŞ05 | 15x15x1.2 | 0.097 |
| AYŞ06 | 15x15x1.3 | 0.105 |
| AYŞ07 | 15x15x1.5 | 0.122 |
| AYŞ08 | 15x15x2 | 0.162 |
| AYŞ09 | 20x20x0.9 | 0.097 |
| AYŞ10 | 20x20x1 | 0.108 |
| AYŞ11 | 20x20x1.1 | 0.119 |
| AYŞ12 | 20x20x1.2 | 0.13 |
| AYŞ13 | 20x20x1.3 | 0.14 |
| AYŞ14 | 20x20x1.4 | 0.151 |
| AYŞ15 | 20x20x1.5 | 0.162 |
| AYŞ16 | 20x20x1.8 | 0.194 |
| AYŞ17 | 20x20x2 | 0.216 |
| AYŞ18 | 20x20x3 | 0.324 |
| AYŞ19 | 25x25x1 | 0.135 |
| AYŞ20 | 25x25x1.1 | 0.149 |
| AYŞ21 | 25x25x1.2 | 0.162 |
| AYŞ22 | 25x25x1.5 | 0.203 |
| AYŞ23 | 25x25x2 | 0.27 |
| AYŞ24 | 30x30x1 | 0.162 |
| AYŞ25 | 30x30x1.1 | 0.178 |
| AYŞ26 | 30x30x1.2 | 0.194 |
| AYŞ27 | 30x30x1.3 | 0.211 |
| AYŞ28 | 30x30x1.5 | 0.243 |
| AYŞ29 | 30x30x2 | 0.324 |
| AYŞ30 | 30x30x3 | 0.486 |
| AYŞ31 | 35x35x2 | 0.378 |
| AYŞ32 | 35x35x3 | 0.567 |
| AYŞ33 | 40x40x1 | 0.216 |
| AYŞ34 | 40x40x1.2 | 0.259 |
| AYŞ35 | 40x40x1.5 | 0.324 |
| AYŞ36 | 40x40x2 | 0.432 |
| AYŞ37 | 40x40x3 | 0.648 |
| AYŞ38 | 40x40x4 | 0.864 |
| AYŞ39 | 40x40x6 | 1.296 |
| AYŞ40 | 45x45x2 | 0.486 |
| AYŞ41 | 50x50x1.5 | 0.405 |
| AYŞ42 | 50x50x1.6 | 0.432 |
| AYŞ43 | 50x50x2 | 0.54 |
| AYŞ44 | 50x50x3 | 0.81 |
| AYŞ45 | 50x50x4 | 1.08 |
| AYŞ46 | 50x50x5 | 1.35 |
| AYŞ47 | 55x55x3 | 0.891 |
| AYŞ48 | 60x60x2 | 0.648 |
| AYŞ49 | 60x60x5 | 1.62 |
| AYŞ50 | 60x60x6 | 1.944 |
| AYŞ51 | 65x65x13 | 4.563 |
| AYŞ52 | 70x70x7 | 2.646 |
| AYŞ53 | 80x80x2 | 0.864 |
| AYŞ54 | 80x80x8 | 3.456 |
| AYŞ55 | 80x80x10 | 4.32 |
| AYŞ56 | 100x100x1.5 | 0.81 |
| AYŞ57 | 100x100x2.5 | 1.35 |
| AYŞ58 | 100x100x10 | 5.4 |
| AYŞ59 | 110x110x10 | 5.94 |
| AYŞ60 | 120x120x10 | 6.48 |
No matching size. Contact us for custom dies.
Sizes in the chart are written as leg × leg × wall thickness. 30x30x3, for example, is an equal angle with two 30 mm legs and a 3 mm wall. The leg length is measured from the outer corner to the end of the leg.
A practical formula for weight per metre is kg/m ≈ 2 × leg × wall × 0.0027. For 30x30x3 that gives 2 × 30 × 3 × 0.0027 = 0.486 kg/m; the chart values are given on this basis. Because this counts the corner where the two legs meet twice, it gives a result a few percent high. For a more precise figure use (2 × leg − wall) × wall × 0.0027, which gives 0.462 kg/m for 30x30x3. The actual weight falls between the two, depending on the corner radius.
The chart covers 60 equal angles in 17 different leg sizes, from 10 mm to 120 mm. Thin-wall angles suit edge protection, trims and decorative finishes, while thick-wall angles are chosen for brackets, frames and structural work. For load-bearing use, the wall thickness should follow the structural calculation of the project. For unequal-leg sizes, send us the dimensions you need.
Wall thicknesses available in the chart for the leg sizes asked for most often. Type the size into the search box above (for example 30x30) to see every option with its weight per metre.
| 15x15 mm | 1 · 1.1 · 1.2 · 1.3 · 1.5 · 2 mm |
|---|---|
| 20x20 mm | 0.9 · 1 · 1.1 · 1.2 · 1.3 · 1.4 · 1.5 · 1.8 · 2 · 3 mm |
| 25x25 mm | 1 · 1.1 · 1.2 · 1.5 · 2 mm |
| 30x30 mm | 1 · 1.1 · 1.2 · 1.3 · 1.5 · 2 · 3 mm |
| 40x40 mm | 1 · 1.2 · 1.5 · 2 · 3 · 4 · 6 mm |
| 50x50 mm | 1.5 · 1.6 · 2 · 3 · 4 · 5 mm |
| 60x60 mm | 2 · 5 · 6 mm |
| 80x80 mm | 2 · 8 · 10 mm |
| 100x100 mm | 1.5 · 2.5 · 10 mm |
An equal-leg angle has two legs of the same length. An unequal-leg angle has one longer leg and is preferred where the load acts mainly in one direction.
Not at the die stage, but our mechanical processing department can drill holes at any spacing you specify.
The practical calculation is 2 × leg × wall thickness × 0.0027; the chart values are given on this basis. For a more precise figure use (2 × leg − wall thickness) × wall thickness × 0.0027.
Extruded profiles are generally produced in 6000-series (aluminium-magnesium-silicon) alloys. We confirm the alloy and temper you need at the quotation stage. Incoming material is verified in our own test centre and shipments are supplied with an analysis report.
Yes. We cut to the length you need, and with drilling and milling we can deliver parts ready for assembly.
Anodising keeps the metallic look of aluminium and strengthens its natural oxide layer. Powder coating gives a specific RAL colour in a matt, gloss or textured finish. The right choice depends on where the profile will be used and the appearance you want.
Send us your technical drawing or a sample and we will quote for tooling and production.
Request a quote
Aluminium Round Tube Profiles
Aluminium Box Profiles
Aluminium Flat Bars
Aluminium Furniture Profiles
Shower Cabin Profiles
Glass Balcony Profiles